After the completion of the laminate flooring and solid wood flooring, how to inspect it? As the saying goes, the quality of the wood floor pavement is seven-point installation. This shows the importance of installation. In fact, there is a difference between the flooring and the solid wood flooring. Different specific procedures are not the same. Today Xiao Bian collected some information to let everyone know about the steps to strengthen the floor and the installation of wood floors, in addition there will also be how to check the relevant points of the strengthening of the flooring and solid wood flooring, we Let's learn it together.
| First, strengthen the flooring and solid wood flooring before the pavement |
1, wooden floor pavement base treatment
The first step in paving the floor is grassroots processing. The grassroots treatment is mainly focused on the five major problems of “sand, tide, concave, convex, and cracked†on the ground, and the ground is repaired to form a new grassroots layer so as to prevent the arching of the floor caused by the emptying and cracking of the original grassroots.
2, paving the floor of the wooden floor leveling the ground
After doing a good job at the grassroots level, we need to level the ground. If the ground is uneven, not only will there be gaps in the baseboard, but the overall floor will also be uneven and there will be abnormal sounds, which will also seriously affect the quality of the floor.
Self-leveling and leveling construction is one of the most advanced ground construction technologies on the market. It can ensure that the difference between the height of every two square meters of the original ground does not exceed 3 mm. During construction, workers mix a variety of materials with water into a liquid substance. After pouring it into the ground, the liquid substance can flow according to the unevenness of the ground, automatically level the ground, and quickly dry and solidify. The ground will form a smooth, flat, seamless new base.
Self-leveling can make the floor more flat and ensure the floor's quiet effect. At the same time, it will make the ground stronger and avoid arching under the floor. In addition, it also ensures that there is no air barrier between the floor and the floor, which increases the thermal conductivity of the floor. If you do a general cement leveling, be sure to allow time for the cement to fully dry. Can not be installed when there is moisture on the ground. There is a simple method to measure moisture. Cover it with 60cm square plastic film on the ground and seal it around. After 24 hours, observe the film has no moisture. If there is moisture in the film, it cannot be installed. In addition, if the ground The difference in height between square meters is more than 5mm and it cannot be installed.
| Second, strengthen the floor and solid wood floor pavement inspection |
1, see. See if the floor color is the same
If the color difference is too large (as shown in the figure), it has a direct impact on the aesthetics and can be exchanged (especially solid wood flooring and laminate flooring); if the colors are too uniform, there is almost no color difference, it depends on whether the floor surface pattern is the same. In general, the patterns on the surface of solid wood flooring and reinforced wood flooring should be different for each piece, while the laminate flooring is the same pattern for each piece.
2, step on. Look at the floor for sound
During acceptance, walk on the floor back and forth, focus on footsteps, pay more attention to acceptance in the area of ​​the wall and the door hole. If you find a part with sound, repeat the walk to determine the specific location of the sound, and then use chalk to mark. In this case, you can ask to remove the resurfacing.
3, amount and touch! To see if the floor deformation, warping
This requires the use of tools. Acceptance method is to use a 2 meter long ruler, leaning on the floor, the flatness should not exceed 3 mm. Remember to measure a few more places. If the passing rate is more than 80%, it is regarded as qualified. In addition, you can touch the corner of the floor and the floor to see if it is flat.
4, close the door. Whether the checker bar is stable
Households that have basically installed wooden flooring will install door clasps. Generally, they should be installed just below the door. It is best to leave the inside and outside without any edges.
Summary: After reading so many notices about strengthening and solid wood flooring, we have a certain understanding of the whole process. If wood flooring is installed, we must follow the above steps for acceptance. If problems arise, communicate with workers in time. solve.
Flooring Flooring Flooring Flooring Cement
Indoor Light,Indoor Wall Lamp,Modern Style Indoor Wall Lamps,Led Down Light Indoor
Shenzhen You&My Electronic Technology Co., Ltd , https://www1.nbyoumysolarlight.com