Tiles are a very important material in the decoration of the home , and they are also used in the most used materials, so the laying of tiles is a very important procedure. Tile paving is a craftsmanship, there are many ideas to pay attention to, we need to understand the ability to make your home tiles suitable for the home, adding an atmosphere to the home. Then follow the decoration home network Xiaobian to learn about the relevant content!
First, wall tiles
1. The wall tiles should be laid from the bottom to the top, and one wall can not be attached to the top at one time. The joints are generally 1~3 mm; the surface of the wall should be treated before the paving, and the cracks should be treated; the application of the bonding materials should be slightly in the middle. Above four weeks, the surface is fixed with a rubber hammer to prevent air from accumulating in the bonding layer. At the same time, horizontal inspection is required; the bonding material should be properly selected. Generally, the ratio of cement to sand on the wall is 1:4, and the ratio of cement to sand on the ground is 1:3.
2, first sweep the surface wet, with a 1:3 cement mortar base, thickness 6 mm. The wall should be slightly hairy, but it must be flat. To calculate the number of vertical and horizontal blocks, determine the horizontal division. Paste the tiles every 3-4 days after the end of the game. When tiling, first water the wet wall, and place the pad on the bottom of the bottom layer of the tile. The pad must be horizontal and secure it.
3, the tiles should be pre-soaked with water to remove a little dry, sticking up from the paddle board. Adding an appropriate amount of 3-4% 107 glue to 1:2 cement fine sand can improve the workability of the mortar. Slow down the setting time. To facilitate paste and prevent mortar from flowing. Apply the mortar to the back of the tile and affix it to the wall and tap the brick surface with a rubber mallet to fill the mortar.
4. After the bottom layer of ceramic tile is pasted, it will be placed vertically as a vertical standard. When affixing, it usually starts from a positive angle, so that the tiles are not aligned. All vertical and horizontal joints must be aligned. The mortar on the brick surface should be wiped off when it is not dry. After the paste is finished, rinse it with clean water and dry it with white cement.
5, tiling on the cement mortar plastering wall to find the vertical and horizontal reference line on the wall, calculate the number of layers, and then paste with cement paste mixed with 5-7%107 glue. If the wall is very flat, first sweep it with pure cement and start to paste when it is not dry. Since the bonding layer is not sand-mixed, it is very thin, only 2-3 mm thick, and is easy to level when bonded, so this is a very convenient and economical method.
Third, other matters needing attention
Paving the large surface: the paving of the large surface is carried out with the standard height surface paved as the standard. The paving is applied close to the paved standard height surface, and the straight line is used to control the tile pair. Straight stitching. When laying the cement, the cement slurry should be fully dried on the back of the tile and hammered with a rubber mallet to prevent the hollowing phenomenon. And check the correction with a level ruler while laying on the side. Immediately wipe off the surface of the cement slurry.
The above is a detailed answer to the Xiaobian, I don't know if you are satisfied with the introduction of the decoration home network Xiaobian~ If you want to know more about the exciting content, please continue to pay attention to our decoration encyclopedia!
More related wonderful reading:
What common sense is there to decorate at home? Precautions when you want to decorate your home
Other Track Bolt styles
Materials: Steel Q235, 35#, 45#; Alloy Steel 40Cr, 42CrMo, 35CrMo
Grade: 4.6/4.8/5.6/5.8/8.8/10.9/12.9, AREMA Gr5/Gr8
Standard: AREMA, UIC, DIN, BS, GOST, NF, JIS, GB/TB, AS or required specification from clients
Type: Fish Bolt/ Frog Bolt/ Clip Bolt/ Clamp bolt
Surface: Plain Oiled, Oxygen Black, Zinc Plated, Hot Dip Galvanized, Dacro coating
Most popular bolt:
Fish bolts with button head and square head are most popular, with specifications as below:|
Type |
Button head oval neck fish bolt |
|||
|
Button head diamond neck fish bolt |
||||
|
Square head fish bolt |
||||
|
Grade |
4.6 |
5.6 |
8.8 |
10.9 |
|
Material |
Q235 |
35# |
45# |
40Cr |
|
Mechanical properties |
Tensile strength:≥400Mpa |
Tensile strength:≥500Mpa |
Tensile strength:≥800Mpa |
Tensile strength:≥1000Mpa |
|
Yield strength:≥240Mpa |
Yield strength:≥300Mpa |
Yield strength:≥640Mpa |
Yield strength:≥900Mpa |
|
|
Elongation:≥22% |
Elongation:≥20% |
Elongation:≥12% |
Elongation:≥9% |
|
|
Cold bending:90 degree without crack |
Cold bending:90 degree without crack |
Cold bending:90 degree without crack |
Cold bending:90 degree without crack |
|
|
Surface |
Plain (oiled), Oxide black, Zinc, HDG, wax, bitumen, Dacromet, Sherardizing |
|||
|
Standard refers |
AS, BS 64, DIN, AREMA/SAE,NF,JIS |
|||
Accessories
* Nut:
Type: square nut/heavy square nut/hex nut/heavy hex nut/flange nut/slotted nut/lock nut/wrench nut, etc.
Material:Steel Q235, 35#, 45#; Alloy Steel 40Cr, 42CrMo, 35CrMo
Grade: 4/5/8/10/12, AREMA ,SAE J995
Surface: Plain Oiled, Oxygen Black, Zinc Plated, Hot Dip Galvanized, Dacro coating
*Spring washer
Material: 65MN/60Si2Mn
Grade: AREMA 1967/ GB
Surface: Plain Oiled, Oxygen Black, Zinc Plated, Hot Dip Galvanized, Dacro coating
Other bolt styles
*Clip bolt for tension clip
*Clamp bolt for clamp
* Frog bolt for turnout: square head bolt/thin square head drilled bolt/BHON bolt
*Tunnel bolt: Spear bolt/ curved bolt
Crane Through Bolt,Crane Rail Fixing Clips,Rail Clip Bolt,Crane Rail Clip Bolt
TAICANG ZHONGBO RAILWAY FASTENING CO., LTD. , https://www.railfastener.com