The installation of floor heating in the home is the most common thing for us, and it is also an indispensable part of our modern family. Therefore, for the first time the owner of the decoration, the understanding of the floor heating trap may not be enough. Regardless of material selection or construction, it is difficult to understand . Next, we will introduce the geothermal water separator installation and related knowledge of geothermal traps. 
Geothermal water separator installation
1. The installation of geothermal water separators is not for professionals. They don't know where to start. Let's take a look at each loop heating pipe of geothermal water separators. Separate the water separators at the inlet and outlet. Water collector connection. The inner diameter of the water separator and water collector should not be less than the inner diameter of the total supply and return pipe, and the maximum sectional flow rate of the water separator and water collector should not be greater than 0.8m/s. The branch circuit of each water separator and water collector should not be much. At 8 Road. Excessive loops will lead to over-concentration of pipes at the manifold, which is not conducive to installation. Copper valve and other shut-off valves should be installed on the return and return pipes of each branch circuit. 
2, then we will be in the water supply pipe of the water separator, according to the direction of its water flow, and then to the valve and filter, as well as discharge pipe to the installation. Then two valves are set before the water separator, which is mainly used for cleaning the filter, and for replacing or repairing the heat metering device. The filter is used to prevent impurities from clogging the flow meter and the heating tube. Valves and filters in front of the heat metering device may also be replaced by a filter ball valve. A water discharge pipe shall be installed on the return water connection pipe after the water catcher, and a balancing valve or other shutoff regulating valve shall be installed.
3, there is a water separator and water collector, we are best able to install the upper air release valve, so that when consumers use it can be more convenient, avoiding the cold and hot pressure and replenishment and other factors caused by the gas gathering , And make the system run blocked. Between their inlet and outlet pipes, we are better to install the bypass pipe, because it can set the valve, and its connection position should be between the beginning of the total inlet pipe and the end of the total outlet pipe to ensure the flushing of the heating piping system. Water does not flow into the heating tube. 
Geothermal traps considerations
1. When the geothermal water separator is in use, we must start hot water heating after it is put into place, that is, first open the valve of the water distribution system of the water separator. Then gradually increase the temperature of the hot water to the pipeline and then circulate. Check the water separator for excuse of water leakage. Then gradually open the valves of the branches of the water separator. If you find that there is water leakage in the pipeline, please close the water supply valve promptly to inform the geothermal or developers to deal with the problem.
2, geothermal water separator is actually to control the temperature in all areas of the home, so consumers can follow individual needs, and then adjust the temperature in each room. After the exhaust manifold manual exhaust valve is used, remember to remove the air in the warm water separator to ensure the heating temperature of each pipe and the flow of the water. There is a filter in the front section of the water separator. When the user uses it for three or five months during heating every year, the filter is cleaned once to ensure the cleanliness of the water pipe. After the heating is completed, the filter is rinsed with water. . 
The above is about the installation of geothermal water separators and the use of geothermal water separators. We hope these will be helpful to everyone. If you still don't understand where you can pay attention to more news, if you want to learn more about this news, please continue to pay attention to our website.
PVD is an innovative technology that can deposit very fine and thin metal films on products. Applied to stainless steel sinks, this technology ensures the durability and longevity of the product's color and helps maintain its beauty. Nano-coating makes the sink antibacterial, waterproof and oil resistant. We also support custom handmade sinks, so sinks can be customized to the size and color you need.
Nano Sink,Black Sink Kitchen,Nano Gold Sink,Nano Granite Sink
JIANGMEN MEIAO KITCHEN AND BATH CO.,LTD , https://www.jmmeiao.com