- Model NO.: XHCK-01
- Automatic Grade: Manual
- Type: Hydraulic Crimping Tools
- Type of A/C Hose: Standard / Reduced Barrier Refrigerant Hose
- Maximum Travel of Piston: 14 mm
- Transport Package: Plastic Box
- Origin: China
- Condition: New
- Usage: Hydraulic
- Product Name: Hydraulic Crimper
- Piston Forces: 80 Kn
- Trademark: XHnotion
- Specification: #6 5/16′′, #8 13/32′′, #10 1/2, #12 5/8′′
- HS Code: 8204200000
Tool Set
Â
| Product Name | Hydraulic Crimper | ||
| Piston Forces | 80 KN | ||
| Maximum Travel of Piston | 14mm | ||
| Hose  Dimension | Nominal diameter, DN, 5/16"~5/8" (Reference outer diameter: Φ17~Φ30 at 2MPa) |
||
| Standard Module Group | 7 | ||
| Operation Mode | Manual | ||
| Ambient Temperature | -10~60ºC | ||
| Arm Strength | ≤75Kg | ||
| Crimping Time | About  10 S | ||
| Noise Level | ≤10 db (Not detected) | ||
| Appearance Dimension (L x W x H) | 780mm x 412mm x 43mm | ||
| Weight | 4.73Kg |
Â
| N0. | Hose Size Inner Diameter (in) |
Hose Size Inner Diameter (in) |
O.D.with 2 Mpa Standard Hose |
The Jaw Size When Grinding Tool Limit Vallue (mm) |
| 6SRB | 5/16" | Φ7.9     Dn8 | D: Φ14~16 d: Φ7.5~9 |
Φ12.5 |
| 6, 8SRB | 5/16"  (Thick walled tube) | Φ7.9     Dn8 | D: Φ16~20  d: Φ7.5~12 |
Φ14.5 |
| 13/32" (Thick walled tube) | Φ10.3    Dn10 | |||
| 10SRB | 1/2" | Φ12.7    Dn15 | D: Φ20~22 d: Φ12~14 |
Φ16.5 |
| 12SRB | 5/8" | Φ15.9    Dn16 | D: Φ22~24 d: Φ14~16 |
Φ21 |
| 8 | 13/32" | Φ10.3    Dn10 | D: Φ22~24 d: Φ10~12 |
Φ20 |
| 10 | 1/2" | Φ12.7    Dn15 | D: Φ22~26 d: Φ12~14 |
Φ21 |
| 12 | 5/8" | Φ15.9     Dn16 | D: Φ27~30 d: Φ15~17 |
Φ24.5 |
Note: Be sure to use correct size die set !
      Failure to do could cause leakage or failure of the crimping.
Â
Pre-Operation Set-Up
2. Rotate the yoke fully counter clockwise to bottom out the adapter seat.
Â
Operating Instructions
2. Select correct die set.
3. Insert the die into yoke.
4. Position fitting and hose in the crimper and close the yoke.
5. Insert pin securely.
6. Turn body of tool clockwise until dies are snug against hose fitting.
7. Turn hydraulic valve to CLOSE position.Â
8. Pump handle to crimp fitting onto hose, continue pumping until handle comes to a stop.Â
9. Once crimp is complete,turn hydraulic valve to OPEN position.
10. Turn body of tool counter clockwise until top yoke can be rotated away from piston portion of yoke.Â
11. Romove holding pin and open yoke.
12. Remove hose assembly.
XHnotion hydraulic crimper can crimp 20000pcs hose joints.
According to the manual instruction, the hydraulic crimper can ensures no oil spilling and fully meet the design requirement.
Â
Â
Â
Â
Packing:
Plastic Box + Carton Box
Custom packaging are available, XHnotion brand packaging are available
Shipping:
Method: Air, Sea, Courier
Export port: Ningbo or Shanghai, China
Delivery time: 3 days to 30 days depends on actual orders.
Express: TNT, UPS, DHL, FedEx, SF Express.
Â
Â
1. Check if hydraulic crimper function normally. Any damaged tool is never used and shall be sent to      the authorized repair shop or our company.
2. Check that the parts at the mouth of hydraulic crimper can freely move. Periodically check that all
    the pipes, axes, and screws are not damaged. Any damaged part must be replaced with original
   part by the authorized technician.
3. After that, the hydraulic crimper shall be thoroughly cleaned. All the moving parts are greased only
   with premium hydraulic oil or ball bearing oil.Â
4. Other maiintenance: Adjustment and maintenance must be performend by the our company
   authorized technicians.
5. If the seal is damaged, the quality assurance will not be cancelled.
6.The hydraulic crimper, which have undergone 20000 crimping operations or have been used for two
   years, whichever is earlier, must be maintained by the authorized repair shop or our company.
7.The hydraulic crimper are sent only after hydraulic oil must be thoroughly drained from them.
8. Associated hydraulic oil: HB30(acid number: 0.81 mg KOH/g) 57ml.
Â
XHnotion originate from notion between pneumatic power and human.
(X stands for winds, H stands for human)
In Chinese, XHnotion stands for 'we do, we promise' Â we read it 'X-notion'.
The company XHnotion Pneumatic was founded in 2007 and has developed with a steadily growing success to a reliable partner for international established clients.
This success of the company XHnotion Pneumatic is based on:
High class quality standard
Customer satisfaction
Fair price policy
Flexibility
The high-class quality standard of the products of company XHnotion is reflected in our quality management system, certificated ISO 9001:2008. And we got CE, RoHS, REACH certificate for international market.Â
XHnotion Pneumatic manufactures below products:
Pneumatic Components:Â air cylinder, solenoid valve, FRL
Solenoid Calve:Â standard solenoid valve, multipurpose solenoid valve, pneumatic angle valve
Pneumatic Fittings:Â plastic pneumatic fittings, mental pneumatic fittings, pneumatic muffler, water push in fittings
Air Gun & Couplers:Â pneumatic couplers, air guns, air tool kits
Air Hoses:Â air tubing, PTFE tubes, tube cutter, pipes
Â
Why Choose US?
1. We offer one stop solution.
2. We have molds workshop, die-casting workshop, CNC workshop, plastic injection workshop toÂ
   make sure each part exactly as the drawing and good function.
3. We will reply you within 24 hours.
4. Whatever quantity you are requesting, we always offer you the best quality.
5. 3D drawing, CAD drawing service for custom fittings, hose, valve, cylinder.
FAQ
Payment Terms:
We accept T/T, L/C, Paypal, Western Union,etc.
Â
Samples Policy:
For regular item, samples against your courier account or you pick up from us.
For custom items, we will discuss by email.
Â
Return Policy:Â
We assure you 1 year policy after shipment.Â
If there is any problem during this period, please contact us for support.
Check Valve,Stainless Steel Check Valve,Duckbill Check Valve,Marine Check Valve
Jiangsu Hida Marine Valve Co., Ltd , https://www.haidavalve.com